How To Program Caddx Nx 8 Wiring

ARMING IN “EXIT” MODE EXIT is used when the user is away from the premises

Program Caddx NX8 to dial cell phone without transmitting info I want to program my caddx nx8 to dial my cellphone first, instead of an alarm service. I am aware that no intelligible info will be transmitted to the phone, but just handshake attempts. I have a perfectly working Caddx NX-8 system with two keypads that I'd like to add a third keypad to and I have a question about the wiring. This system came installed with my house but I think I have the wiring figured out. Both keypads are wired directly back to the NX-8 board. Now, I'm assuming I could add the third keypad's wiring back to the. The GE Caddx Networx line of security systems offer many of the features of more complicated alarms, but at very reasonable prices. The 3 main panels are the GE NX-4, NX-6, and the NX-8. The smallest is the NX-4, with 8 on-board zones. The largest panel is the Caddx NX-8, with 8. NX-848-KIT NX-8E control, NX-148 LED keypad, 16.5 V 40 VA transformer. NX-108E 8-zone LED keypad. NX-116E 16-zone LED keypad. NX-124E 24-zone LED keypad. NX-148E Alphanumeric 48-zone LCD keypad. NX-200 Zone doubling kit (includes one hundred 3.74k and one hundred 6.98k resistors). NX-216E 16-zone expander module.

and wants the interior protected (the motion detectors ON).

1. Close all protected doors and windows.

ARMING IN “STAY” MODE STAY is used when the user is inside the premises and

wants protection around the perimeter (the motion

detectors OFF).

2. Press the “STAY” key.

DISARMING SYSTEM Enter code.

2. Enter a master code. The “ready” light will flash.

3. Enter the 2-digit user number (example: “03” for user

4. Enter the new 4-digit user code. Note: To delete a

user code, enter * * * * for a 4-digit code.

5. The ready light will flash. If the code is rejected, the

6. If another user code needs to be programmed,

7. Press the “#” key while the ready light is flashing to

exit the User Code Programming Mode.

BYPASSING ZONES System must be in disarmed state.

2. Enter 1 or 2 digits indicating the zone you wish to

bypass. (Example: Press the “1” key for zone 1,

Caddx Nx 8 Installation Manual

press “1” then “2” for zone 12.)

4. The corresponding zone light will illuminate indicating

the zone has been bypassed. Repeat steps #2 and #3 for

any other zone(s) that need to be bypassed.

5. Press the “#” key to exit the Bypass Mode. The bypass

light will stop flashing upon exiting the Bypass Mode.

All zones will automatically be unbypassed each time the

How To Program Caddx Nx 8 Wiring Diagram

system is disarmed.

VIEW ALARM MEMORY 1. Press “8” “3.” The zone(s) that created the last alarm

2. The ALARM MEMORY feature will flash those zones

that created alarms and will light steady those zones that

were bypassed during the last alarm.

IDENTIFYING TROUBLES

FLASHING ARMED LIGHT The armed light will flash when there has been

an alarm during the previous arm cycle.

POWER LIGHT OFF No AC power.

POWER LIGHT FLASHING Low system battery.

FIRE LIGHT FLASHING Trouble with fire device or wiring.

ZONE LIGHT FLASHING RAPIDLY A zone is in a trouble condition.

SERVICE LIGHT IS ON Press “*2” for further information (indicated by

zone lights).

Zone 1 – System fault.

Zone 2 – Zone tamper.

Zone 5 – Zone trouble.

Zone 6 – Telephone trouble.

Zone 7 – Dialer failure.

Zone 8 – System lost time.

Enter “#” to exit mode.

ENTER CODE TO SILENCE TROUBLE BEEPS.

ENTER “*7” TO ATTEMPT TO RESET TROUBLES.

ENTER CODE TO CLEAR SERVICE LIGHT AFTER A PHONE TROUBLE HAS BEEN CLEARED.

SET CLOCK 1. Press “*97.”

3. Enter time as 4-digit military time.